Allied Telesis 86241-02 Release Note Download Page 7

Patch 86241-02 For Rapier Switches and AR800 Series Modular Switching Routers

7

Patch 86241-02 for Software Release 2.4.1
C613-10340-00 REV B

Address learning on the mirror port is now correctly re-enabled when it is 
no longer the mirror port.

New commands have been added to enable the addition and deletion of 
static multicast addresses to and from the multicast forwarding table. The 
new commands are:

ADD SWITCH MULTICASTADDRESS IP=

ipadd

 VLAN=

vlan-id

 

PORT=

port-list

DELETE SWITCH MULTICASTADDRESS IP=

ipadd

 VLAN=

vlan-id

When the SET IP ROUTE command was executed to change any parameter 
other than METRIC1, which is the RIP metric, the RIP metric was reset to 1. 
This metric is now only updated if a value for the parameter is specified.

When the system time was set to a time that was before or significantly after 
the current time, Firewall sessions were prematurely deleted. This issue has 
been resolved.

When the PPP ONLINELIMIT was exceeded for PPP over TDM, the PPP 
link stayed open, allowing Link Quality Report (LQR) packets to be 
transmitted. This caused the 

ifOutOctets

 counter to increment. Now, if the 

ONLINELIMIT is exceeded, the link will close.

Entering 63 for the EPORT parameter in the ADD SWITCH L3FILTER 
command caused a fatal error. This parameter now accepts the values 63 
and 64.

The SHOW VRRP command now shows the number of trigger activations 
for the Upmaster and Downmaster triggers.

After a prune lifetime had expired, the interface was not joined back to the 
DVMRP multicast delivery tree. This issue has been resolved.

The following issues have been resolved:

It was possible to assign the same network on different IPV6 interfaces

The loopback address was being added to other interfaces

The tunnel configuration was not showing correctly in IPV6 
configuration commands

RIPv6 now sets the metric of routes for interfaces that are DOWN to 16, and 
immediately sends responses when the link status of VLAN interfaces 
changes.

PCR: 02365

Module: SWI

Network affecting: No

PCR: 02367

Module: SWI

Network affecting: No

PCR: 02369

Module: IPG

Network affecting: No

PCR: 02371

Module: FIREWALL

Network affecting: No

PCR: 02376

Module: PPP

Network affecting: No

PCR: 02378

Module: SWI

Network affecting: No

PCR: 02395

Module: VRRP, TRG

Network affecting: No

PCR: 02397

Module: DVMRP

Network affecting: No

PCR: 02398

Module: IPV6

Network affecting: No

Summary of Contents for 86241-02













Reviews: