Allied Telesis 86241-02 Release Note Download Page 6

6

Patch Release Note

Patch 86241-02 for Software Release 2.4.1

C613-10340-00 REV B

It is now possible to set a preference value for dynamically learned routes 
based on their protocol using the command:

SET IP ROUTE PREFERENCE={DEFAULT|1..65535} 

PROTOCOL={BGP-EXT|BGP-INT|OSPF-EXT1|OSPF-EXT2|OSPF-INTER|

OSPF-INTRA|OSPF-OTHER|RIP}

The CREATE CONFIGURATION command was not correctly generating 
the DISABLE SWITCH HWFILTER and DISABLE SWITCH L3FILTER 
commands. This issue has been resolved.

When the PAC card was under severe load, the related driver occasionally 
did not fully transfer all result data from the chip. This caused an 

actCmdFail

 

error. This issue has been resolved.

In a previous patch, a fatal error occurred after a RESTART ROUTER 
command was executed when using PPP over SYN. Also, on AR745 
models, PPP was using an 8 MB boundary instead of a 16 MB boundary. 
These issues have been resolved.

The following issues have been resolved:

PIM was not sending Hello messages over a Frame Relay (FR) interface.

A fatal error occurred if 64 was entered as the interface value in the 
DESTROY FRAMERELAY command. The command now only accepts 
0-63 for this parameter.

The ADD FRAMERELAY DLC command incorrectly accepted a TYPE 
parameter. Also, this command was not accepting the 
ENCAPSULATION parameter.

The CREATE CONFIGURATION command incorrectly generated the 
CIR and CIRLIMITED parameters for the ADD FRAMERELAY DLC 
command.

FR interfaces with static DLCs were always shown as DOWN. The 
status of the interface was not being updated when a circuit was added 
to the interface.

When an IP Multihomed interface was used as an OSPF interface, 
neighbour relationships were only established if the IP interface for OSPF 
was added first in the configuration. Now, OSPF establishes neighbour 
relationships regardless of the IP Multihomed interface configuration order.

The FLASH compaction process is now transparent to the file edition 
process. The FLASH system is now more stable.

PCR: 02346

Module: BGP, IPG

Network affecting: No

PCR: 02347

Module: SWI

Network affecting: No

PCR: 02348

Module: ENCO

Network affecting: No

PCR: 02354

Module: SCC, SYN, PPP

Network affecting: No

PCR: 02357

Module: FR

Network affecting: No

PCR: 02359

Module: IPG

Network affecting: No

PCR: 02363

Module: FFS, FILE, TTY

Network affecting: No

Summary of Contents for 86241-02













Reviews: