Washer Operation
Power Up
When power is applied to the washer, the control will display its
control type as
tL
, software version as
S---
(
---
is the version
number) and software subversion as
.--
for one (1) second. If the
control was not powered down during a running cycle, it will en-
ter the Ready Mode.
Ready Mode
In this mode of operation, the display shows the current selected
cycle, modifier, temperature and the full current vend price for
that cycle. The INSERT COINS/CARD LED is lit.
To start the cycle, the user must satisfy the vend price and then
press the START keypad.
The user will be able to select a different cycle/wash water tem-
perature or modifier by pressing a cycle pad when the machine is
in the ready mode or before the first fill is complete.
Partial Vend Mode
The control enters this mode when part of the vend price has been
entered, but not enough vend is entered to satisfy the vend price.
The control will display the remaining vend price needed to start
the cycle and the INSERT COINS/CARD LED is lit.
Additional Vend Mode
The control enters this mode if a change is made before the first
fill is complete. If the vend price is not satisfied within one (1)
minute, the washer control will go back to the first selection and
the cycle will continue. Pressing the START keypad will cancel
cycle changes and exit this mode. After the first fill, all key
presses will be ignored, allowing the washer to go through the
complete cycle.
Start Mode
The control enters this mode when the full vend price is satisfied,
the vend price is zero, or the control is in OPL Mode. The
START pad LED will flash one (1) second on and one (1) second
off. If Start Mode is entered because the vend price is satisfied or
the control is in OPL Mode, the display will show
PUSH
for one
(1) second,
StArt
for one (1) second and the current cycle time
for one (1) second. If Start Mode is entered because the vend
price is zero (0), the display will show
FrEE
. When first entering
Start Mode, a signal will sound for one (1) second on and one (1)
second off for 10 seconds if Signal for Start is enabled.
End of Cycle Mode
When a cycle is complete, the control will display
00
until the
washer is opened, a key is pressed, or a coin/card is entered.
When one of these three options occurs, the display will revert
back to the ready mode.
Cycle Sequence
Upon the start of a cycle, the control will display the total cycle
time. The appropriate LEDs will light while the machine passes
through different cycle steps. Any coin entered after the first fill
completes will be added to the total coin counter, but the user will
not be able to change cycles.
Signals
There are five options when a signal can be used during the
washer operation. These five options are listed below:
1.
End of Cycle Signal
By default, this signal is turned off. If
turned on, the signal sounds for three (3) seconds at the end of
a cycle.
2.
Signal On Keypad Depression
By default, this signal is
turned on and sounds for a quarter of a second each time a
keypad is pressed.
3.
Signal On Coin Input/Card Insertion
By default, this signal
is turned on and will sound for a quarter of a second each time
a coin or card is entered.
4.
Signal for Serial or Network Vending Command
By de-
fault, this signal is turned on for a quarter of a second when
the control receives a valid serial or network vend command.
5.
Signal for Start
By default, this signal is turned on and will
sound one (1) second on and one (1) second off for 10 sec-
onds after vend price has been satisfied.
NOTE: Refer to
options.
Opening the Washer Lid
If the washer lid is opened anytime except the final spin, the dis-
play will show
Lid
and the timer will stop. Once the lid is
closed, the cycle will resume from the point of interruption. If the
lid is opened in the final spin step, the timer will continue to
count down to the end of the cycle. The cycle operation will stop
and the display will show
Lid
. When the timer reaches 0 mi-
nutes, the control will display
00
until a key is pressed, or a coin/
card is entered. When one of these options occur, the display will
revert to the Ready Mode.
Washer Operation
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13
Part No. 204370ENR1
Summary of Contents for SWNNC2HP115TQ01
Page 2: ......
