ALLIANCE SCA030FN Original Instructions Manual Download Page 116

Page: 116 / 157

Unable to Access Manual Mode

NOTE: If unable to enter: Manual Programming, Manual Diagnostics and Manual Rapid Advance, make sure they
are not disabled in Programming.

(A)

Is there alternately

5VDC and less than

1VDC at H11-2 &

H11-11 on AP2 control

logic board when

access panel switch

is operated?

(C)

Coin models: Is there

alternately 5VDC and

less than 1VDC at

H11-1 & H11-3 on AP2

control logic board

when coin vault

switch is operated?

Yes

(B)

Inspect wiring and

access panel switch,

Repair/replace as

necessary.

Replace AP2 control

logic board.

Yes

(D)

Coin vault switch

needs to be closed to

access manual mode.

Check switch and

wiring.

Troubleshooting

DO NOT COPY or TRANSMIT

116

Part No. F8677701EN

Summary of Contents for SCA030FN






























































































































































Search results

Summary of Contents for SCA030FN

Reviews:

Related manuals for SCA030FN

Brands by name

Popular brands

ALLIANCE SCA030FN, Original Instructions Manual

Search results

Summary of Contents for SCA030FN

Reviews:

Related manuals for SCA030FN

Brands by name

Popular brands