This option allows the owner to enable or disable third special
vend. Special Vend 3 can be programmed using an external de-
vice or network. The owner may also turn the Special Vend 3 op-
tion on or off.
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad until
Prog
appears in the display. Press the START
(enter) keypad, and
AtS 1
will appear in the display.
3. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to scroll through the programmable options until
SP3
appears in the display.
4. When
SP3
appears in the display, press the START (enter)
keypad. The current Special Vend 3 Days Enable status will
appear in the display.
on
= Option Enabled
oFF
= Option Disabled (factory default setting)
5. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Special Vend 4 Days Enable
SP4
This option allows the owner to enable or disable a fourth special
vend. Special Vend 4 can be programmed using an external de-
vice or network. The owner may also turn the Special Vend 4 op-
tion on or off if desired.
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad until
Prog
appears in the display. Press the START
(enter) keypad, and
AtS 1
will appear in the display.
3. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to scroll through the programmable options until
SP4
appears in the display.
4. When
SP4
appears in the display, press the START (enter)
keypad. The current Special Vend 4 Days Enable status will
appear in the display.
on
= Option Enabled
oFF
= Option Disabled (factory default setting)
5. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to change the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Cycle Modifier Programming
CNP-
This option allows the owner to program the machine to offer an
added prewash, extra wash time, an added rinse, extra rinse time,
a warm rinse, or any combination of the above to the customers
for an added vend price. This option is used when B or C is selec-
ted using the modifier keypad.
How to Program Default Cycle Modifier
CNP 1
This option allows the owner to set the Default Cycle Modifier.
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad until
Prog
appears in the display. Press the START
(enter) keypad, and
AtS 1
will appear in the display.
3. Press the NORMAL 40 (
∧
) or the NORMAL 40 (
∨
) keypad to
scroll through the programmable options until
CNP-
appears
in the display.
4. When
CNP-
appears in the display, press the START (enter)
keypad.
5. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to scroll through the programmable Cycle Modifier
options until
CNP 1
appears in the display.
6. When
CNP 1
appears in the display, press the START (enter)
keypad. A number will appear in the display. This number
corresponds to the current default cycle modifier. Refer to ta-
ble below.
CNP 1
Default Value
Cycle Modifier
0*
A
1
B
2
C
*Factory default setting.
Table 9
7. Press the NORMAL 40 (
∧
) or the DELICATES COLD (
∨
)
keypad to increase or decrease the current number to the de-
sired number selected from the table.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
How to Program Cycle Modifier B Key #1 Options
CNP 2
This option allows the owner to select the options that are ena-
bled when the B modifier keypad is active.
1. Control must be in Manual Mode. Refer to
Programming Control
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
69
Part No. 805405ENR5
Summary of Contents for BT3JGASG403UW01
Page 2: ......
