Alliance Laundry Systems IYG065J Original Instructions Manual Download | Manualshive

Page: 81 / 106

background image

Failure Message Overview

Num-

ber

Failure Mes-

sage

Failure

Action

Fault Occurrence

E44

Model Type

Incorrect selection of machine
type

Make correct selection

Configuration menu

E45

Speed sensor

The drum rotation sensor is not
working

Full stop + tumble

Before spin sequence

E77

Heating Time Out

Heating on Hold Signal Failure Full stop + tumble

Wash step

E80

SoapTimeOut

On Hold Signal Failure Soap
Dispensing System

Full stop + tumble

Whole cycle

E300-
E353

Mits Err

Specific Mitsubishi Inverter
Alarm

Full stop + safety time

Whole cycle

E500-
E526

Memory Err

Memory Error

Full stop + safety time

Any time

E560-
E563

USB Errors

Errors in communication with
USB flash disk

For Informatoion only

Only in Advanced menu Data
Export/Import

E570-
E571

Enh.Debit

Problem with card reader pay-
ment system

For Informatoion only

Whole cycle

E600-
E628

Softw. Err

Software Error

Full stop + safety time

Any time

Table 47

Service Menu

In the Service menu you have some extra utilities:

• The Software Version Number.
• An overview of the 20 last failure messages.
• Statistics for 10 general error messages.
• An overview of the input states.
• Switching On the Inverter for a technical intervention.
• Reset Cycle Counter and Statistics Error Messages.

How to Get into the Service Menu

CFD1387R_SVG

Main Menu

Initialization ...
Program ...
Servis ...
Configuration ...
Advanced ...
Payment Menu ...

Figure 28

The SERVICE menu can only be accessed when the machine is
in standby (the power is switched on, but no program is started).

• The program overview is shown.

• Turn the washing machine to the setup mode. Refer to

Get into the Setup Mode

• The Main menu is now available.
• Press the ARROW DOWN button to select the SERVICE

menu.

• Press the ENTER button to make your selection.
• Now you will see the Service Menu Screen.

CFD1388R_SVG

Service Menu

Diagnostic prog ...
Faults ...
Toolbox ...
Exit ...

Software version: 772. 100.0

Figure 29

Troubleshooting

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

81

Part No. D1631ENR7

«
...
79
80
81
82
83
...
»

Summary of Contents for IYG065J











































































































Reviews:

No comments

Related manuals for IYG065J

Brand: IFB Pages: 33

Brand: Samsung Pages: 96

Brand: ALBERTI Pages: 20

K 4 Universal Edition

Brand: Kärcher Pages: 32

Brand: Indesit Pages: 16

Brand: Gaggenau Pages: 64

FLOORWASH 1000 Battery

Brand: NAMCO Pages: 24

SUNJOE SPX4001-RM

Brand: SNOWJOE Pages: 18

Brand: SPT Pages: 21

Brand: Hisense Pages: 14

T-1200 WC1200XA-12

Brand: Dexter Laundry Pages: 25

Brand: Heinner Pages: 50

Brand: Cam Spray Pages: 13

Brand: Insinger Pages: 2

Brand: Haier Pages: 12

Brand: Haier Pages: 20

Brand: Haier Pages: 20

Brand: Gaggenau Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands