background image

802643

3

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Section 1

Safety Information

Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,” 
“WARNING” and “DANGER”) followed by specific instructions. These precautions are intended for the personal 
safety of the operator, user, servicer, and those maintaining the machine.

a

DANGER

Danger indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

a

WARNING

Warning indicates a hazardous situation that, if not avoided, could cause severe personal injury or death.

a

CAUTION

Caution indicates a hazardous situation that, if not avoided, may cause minor or moderate personal injury or property 
damage.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions. 

IMPORTANT 

The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will 
occur if the procedure is not followed.

NOTE

The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is 
important but not hazard related.

In the interest of safety, some general precautions relating to the operation of this machine follow.

• Failure to install, maintain, and/or operate this machine according to the manufacturer’s 

instructions may result in conditions which can produce serious injury, death and/or property 
damage.

• Do not repair or replace any part of the machine or attempt any servicing unless specifically 

recommended or published in this Service Manual and that you understand and have the 
skills to carry out.

• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the machine is properly grounded and to reduce the risk of fire, 
electric shock, serious injury, or death.

W284

WARNING

Summary of Contents for CTSA7AWN








































































Reviews: