background image

802643

31

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Dryer Troubleshooting

19. Clothes Are Too Hot When Removed From Dryer

Clothes are too hot when 
removed from dryer.

Is exhaust 

system 

improper or 

inadequate?

Refer to 

Installation 
Instructions

 

(supplied with unit) 
for exhaust 
requirements.

Yes

Were clothes 

removed from 

dryer before 

cycle has 

completed?

No

Allow the dryer to 
complete the 
cycle through the 
cool-down to the 
OFF position.

Yes

Is cycling 

thermostat 

inoperative?

Test cycling 
thermostat and 
replace if 
inoperative.

No

Yes

SWD1713S

Are seals 

inoperative 
(air leaks)?

Check and replace any inoperative 
seals in the following areas:
1. Seal between loading door and 
front panel.
2. Seal between front panel and 
front bulkhead.
3. Seal between blower cover and 
air duct.
4. Seal between cylinder and front 
or rear bulkhead.
5. Gap between air duct and filter 
mounting.

Yes

Is timer 

inoperative 

(not allowing 

cool-down)?

Test timer and 
replace if 
inoperative.

No

Yes

No

Summary of Contents for CTSA7AWN








































































Reviews: