background image

052793 - 03/2013

SECTION 1

SAFETY

Page 1-10

 

ALWAYS

 recharge the battery in a well-ventilated environment to avoid the risk of a dangerous con-

centration of combustible gases.

 If the battery liquid (dilute sulfuric acid) comes into contact with

clothing or skin, rinse skin or clothing immediately with plenty of water.

 If the battery liquid (dilute sulfuric acid) comes into contact with eyes, rinse eyes immediately with 

plenty of water and contact the nearest doctor or hospital to seek medical attention.

 

ALWAYS

 disconnect the negative battery terminal before performing service on the equipment.

 

ALWAYS

 keep battery cables in good working condition. Repair or replace all worn cables.

 Side slope operation is not permitted.

 Walk around the riding trowel before starting it to see if any items are worn, damaged, leaking, etc. 

that may make the riding trowel dangerous to operate.

 Stop and inspect the equipment if you strike an object. If necessary, make repairs before restarting.

 

ALWAYS

 check that all controls are functioning properly immediately after start-up!

 

DO NOT

 operate machine unless all controls operate correctly.

General Safety (cont’d)

Summary of Contents for MSP455













































































































Reviews:

Related manuals for MSP455