manualshive.com logo in svg

Allen-Bradley PowerFlex 20-HIM-A6, User Manual

Share
Download
Allen-Bradley PowerFlex 20-HIM-A6 User Manual Download Page 21

Rockwell Automation Publication 20HIM-UM001E-EN-P - May 2017

21

Installing the HIM

Chapter 2

3.

Insert the supplied 3 m/9.8 ft. long 1202-C30 HIM cable into the mating 
socket on the back of the HIM.

4.

Install the supplied O-ring into the cable routing hole on the panel to 
protect the cable.

5.

Route the HIM cable through the cable routing hole on the panel.

6.

Align the six threaded studs of the HIM with the panel clearance holes, 
and place the HIM against the panel.

7.

Tighten the nuts onto the six threaded studs of the HIM extending behind 
the panel.

Recommended torque is 0.68 N•m (6.0 lb•in).

8.

Route the HIM cable to the drive.

9.

Connect the HIM cable to the DPI Port 2 on the drive as shown on 

page 16

 for a PowerFlex 750-Series drive or a PowerFlex 7-Class drive.

Removing the HIM

Remove the HIM from the drive HIM bezel or the remote-mount HIM bezel in 
reverse order of how it was installed.

ATTENTION: 

Risk of injury or equipment damage exists. If the HIM cable or 

remote-mount HIM bezel cable is disconnected from DPI Port 2 on the drive, the 
drive may fault. Determine how the drive will respond before disconnecting the 
cable.

IMPORTANT

The Host drive can remain powered when removing the HIM. However, a fault 
will occur if the HIM is not the last controlling device and does not have Manual 
control of the Host drive. To avoid a fault in this case, access the HIM Control 
screen (shown on 

page 30

), press the 

 key, and then remove the HIM 

from the Host drive.

Summary of Contents for PowerFlex 20-HIM-A6











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands