manualshive.com logo in svg

Allen-Bradley FlexLogix 1794, Reference Manual

Share
Download
Allen-Bradley FlexLogix 1794 Reference Manual Download Page 24

Publication 1794-RM001G-EN-P - December 2011

3-2

        FLEX I/O Modules

Using Digital 
Input Modules

General Considerations when using Any FLEX I/O Digital Input 
Module

Regardless of the type of FLEX I/O input module used, there are a number of 
general application considerations that users must follow when applying these 
modules in a SIL2 application:

•

Proof Tests -

 Periodically (for example, once every several years) a 

System Validation test must be performed. Manually, or automatically, 
test inputs to make sure that all inputs are operational and not stuck in 
the ON or OFF state. Inputs must be cycled from ON to OFF or OFF 
to ON. .

•

Wire sensors to separate input points on two separate modules that are 
on different ControlNet nodes.

•

Configuration parameters (for example, RPI, filter values) must be 
identical between the two modules.

•

The same controller must own both modules.

•

Monitor the ControlNet status bits for the associated module and 
ensure that appropriate action is invoked via the application logic by 
these status bits.

Summary of Contents for FlexLogix 1794





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands