Allen-Bradley Bulletin 2364F Troubleshooting Manual Download Page 17 | Manualshive

Page: 17 / 64

background image

Publication 2364F-5.05 - March 1999

Troubleshooting The RGU

2-5

Damaged Components

Damaged components may be suspected if a loud discharge or melting
smell has come from the RGU. Check the following items to find damaged
components.

Are the AC line fuses in good condition?

Replace

all

the AC line fuses.

Test the IGBTs (as instructed in Chapter 4).

Are any IGBTs damaged?

Replace the damaged IGBTs. Test and

replace the gate driver board and snubber

boards as necessary.

Are the DC bus fuse(s) in good condition?

Replace the damaged fuses.

No

Yes

Yes

No

No

Yes

Check the RGU for melted wiring. Test the

isolation board and gate driver board (as

instructed in Chapter 4). Replace as necessary.

Push the disconnect lever to off and verify zero volts
across the DC bus before testing the following items.

Is there any visible damage to the MOVs?

Replace the MOVs.

Yes

No

!

ATTENTION:

«
...
15
16
17
18
19
...
»

Summary of Contents for Bulletin 2364F

































































Reviews:

No comments

Related manuals for Bulletin 2364F

Varycolor MICRO 150HTI

Brand: JB-Lighting Pages: 18

Brand: Launch Pages: 3

Brand: Launch Pages: 43

Brand: Launch Pages: 8

Brand: Launch Pages: 67

Brand: Launch Pages: 55

Brand: LAUNCH TECH Pages: 14

X-431 PROS V4.0

Brand: Launch Pages: 80

Brand: Hach Pages: 456

Brand: Ultratune Pages: 12

Brand: EzCAP Pages: 15

Pro hunter 2525

Brand: SprotDog Pages: 28

Brand: Ocean Signal Pages: 2

RadioPRO 4 RP4-MZ11

Brand: PAC Pages: 5

Brand: KaVo Pages: 70

Brand: GreenTec Pages: 66

Brand: Slick Pages: 2

TEMSTM POCKET 7.3

Brand: ASCOM Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands