Allen-Bradley 5069-IA16 User Manual Download | Manualshive

Page: 77 / 296

background image

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

77

Features Common to Compact 5000 I/O Digital Modules

Chapter 2

Use CIP Sync Time with Fast
I/O Modules

The following Compact 5000 I/O standard modules use CIP Sync™ for time
stamps and scheduling:

• 5069-IB16F
• 5069-IB6F-3W
• 5069-OB16F

CIP Sync is a CIP™ implementation of the IEEE 1588 PTP (Precision Time
Protocol). CIP Sync provides accurate real-time (Real-World Time) or
Universal Coordinated Time (UTC) synchronization of controllers and
devices that are connected over CIP networks. This technology supports
highly distributed applications that require timestamping, sequence of events
recording, distributed motion control, and increased control coordination.

The 5069-IB16F, 5069-IB6F-3W, and 5069-OB16F modules are CIP Sync
slave-only devices. There must be another module on the network that
functions as a master clock. For more information on how to use CIP Sync
technology, see the Integrated Architecture® System and CIP Sync
Configuration Application Technique, publication

You can use fast Compact 5000 I/O digital modules to capture time stamps
and schedule outputs while providing the following advances:

• Fast I/O modules have much higher precision than other modules.

• Inputs are timestamped by point, so multiple inputs can be configured

for COS without losing time stamp data.

• CIP Sync is system-wide, so time stamp and schedule values are

consistent across all modules in the system.

For example, if you use time stamps on a 5069-IB16F module to
schedule outputs on a 5069-OB16F module, the controller, input
module, and output module are not required to reside in the same local
system. The I/O modules can reside in a remote I/O system.

• Output modules use all 64 bits of the time stamp to schedule, so there

are no limits on schedule ranges.

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

SA P

ow

er

MOD P

ow

er

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

Standard Modules

™

NET B1

LINK B1

NET A1

LINK A1

NET A2

LINK A2

SPEED X1

LINK X1

OK

RUN

FORCE

FAN 1

SD

FAN 2

Compact

Logix

5480

B1

A1

1

2

A2

5069-L46ERMW

CONTROLLER

UPS

MP

SA

R
B
F

R

B

F

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

«
...
75
76
77
78
79
...
»

Summary of Contents for 5069-IA16









































































































































































































































































































Reviews:

No comments

Related manuals for 5069-IA16

Brand: Rain Bird Pages: 9

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 34

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 16

Brand: Toa Pages: 1

Century 2 NCL10000 Series

Brand: BraunAbility Pages: 39

Brand: Cruz Pages: 12

Brand: Goodmans Pages: 22

Brand: Ravaglioli Pages: 102

Brand: Videx Pages: 8

Brand: Farfisa Pages: 8

Brand: Orbit Pages: 1

Brand: Pneumatic Division Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands