Allen-Bradley 5069-IA16 User Manual Download | Manualshive

Page: 73 / 296

background image

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

73

Features Common to Compact 5000 I/O Digital Modules

Chapter 2

Module Inhibiting

Module inhibiting lets you indefinitely suspend a connection, including Listen
Only connections, between an owner-controller and an I/O module without
removing the module from the configuration. This process lets you temporarily
disable a module, such as to perform maintenance.

You can use module inhibiting in the following ways:

• You write a configuration for an I/O module but inhibit the module to

help prevent it from communicating with the owner-controller. The
owner does not establish a connection and the configuration is not sent
to the module until the connection is uninhibited.

• In your application, a controller already owns a module, has downloaded

the configuration to the module, and is exchanging data over the
connection between the devices.

In this case, you can inhibit the module and the connection to the
module does not exist.

You can use module inhibiting in the following instances:

• You want to update an I/O module, for example, update the module

firmware revision. Use this procedure.
a. Inhibit the module.
b. Perform the update.
c. Uninhibit the module.

• You use a program that includes a module that you do not physically

possess yet. You do not want the controller to look for a module that
does not yet exist. In this case, you can inhibit the module in your
program until it physically resides in the proper slot.

You can inhibit the connection to a Compact 5000 I/O digital module on the
Connection category of the Module Properties dialog box.

To see where to inhibit a connection, see the following:

• Compact 5000 I/O standard modules -

• Compact 5000 I/O safety modules -

5069-OBV8S

SIL2 CPU

5069-L3100ERMS2

Compact GuardLogix

5069-OBV8S

5069-IB8S

5069-IB8S

OUTPUT

OUTPUT

SA

Po

w

er

M

O

D

Po

w

er

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

SA P

ow

er

MOD P

ow

er

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

Standard Modules

Safety Modules

™

NET B1

LINK B1

NET A1

LINK A1

NET A2

LINK A2

SPEED X1

LINK X1

OK

RUN

FORCE

FAN 1

SD

FAN 2

Compact

Logix

5480

B1

A1

1

2

A2

5069-L46ERMW

CONTROLLER

UPS

MP

SA

R
B
F

R

B

F

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

IMPORTANT

You cannot inhibit a connection when the controller is safety-locked or a
safety signature exists for the controller.

IMPORTANT

Whenever you inhibit an output module that is ProgMode enabled,
it enters Program mode, and all outputs change to the state
configured for Program mode.

For example, if an output module is configured so that the state of
the outputs transition to zero during Program mode, whenever that
module is inhibited, outputs transition to zero.

«
...
71
72
73
74
75
...
»

Summary of Contents for 5069-IA16









































































































































































































































































































Reviews:

No comments

Related manuals for 5069-IA16

Brand: V-Tec Pages: 4

Brand: M-system Pages: 4

Brand: JBL Pages: 8

Brand: Omniflex Pages: 2

Brand: Skytec Pages: 12

Brand: Ravaglioli Pages: 72

Brand: M-E Pages: 4

Brand: CAME Pages: 32

Brand: M-system Pages: 7

Brand: Grundfos Pages: 27

Brand: NA-DE Pages: 18

Brand: WAGO Pages: 30

Brand: M-system Pages: 4

Terraneo 306000

Brand: Bticino Pages: 4

Brand: Bouyer Pages: 4

Brand: CAME BPT Pages: 16

Brand: XtendLan Pages: 19

Brand: Jacuzzi Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands