Allen-Bradley 5069-IA16 User Manual Download | Manualshive

Page: 65 / 296

background image

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

65

Digital Module Operation in a Control System

Chapter 1

Configuration Signature and Ownership

Every Compact 5000 I/O safety module in a system has a configuration
signature and configuration ownership.

Configuration Signature

Each safety device has a unique configuration signature that defines the
module configuration. The configuration signature includes the following:

• ID number

• Date

• Time

The configuration signature is used to verify a module’s configuration.

Configuration Ownership

The connection between the owner-controller and the Compact 5000 I/O
safety module is based on the following:

• Compact 5000 I/O safety module node number

• Compact 5000 I/O safety module safety network number

• Controller node or slot number

• Controller safety network number

• Path from the controller to the Compact 5000 I/O safety module

• Configuration signature

If any differences are detected, the connection between the owner-controller
and the Compact 5000 I/O safety module is lost, the yellow yield icon appears
in the controller project tree.

IMPORTANT

If the owner-controller is a Compact GuardLogix 5380 controller, the
controller has a node number.

If the owner-controller is a GuardLogix 5580 controller, the
controller has a slot number.

«
...
63
64
65
66
67
...
»

Summary of Contents for 5069-IA16









































































































































































































































































































Reviews:

No comments

Related manuals for 5069-IA16

Brand: JeaTone Pages: 6

Spacemaker 7-5400

Brand: GE Pages: 12

Brand: Dahua Pages: 22

Brand: Quantum Pages: 97

Brand: YASKAWA SIEMENS Pages: 373

Brand: Equalizer Pages: 26

Brand: HK Audio Pages: 20

Brand: Centurion Pages: 12

Brand: BERNSTEIN Pages: 52

Brand: Mercury Pages: 3

CENTRAL ELO-16 GB

Brand: Tyco Fire Product Pages: 4

Brand: Wayne Pages: 1

Hydro-Guard HG-4

Brand: Mueller Pages: 8

Brand: Fancom Pages: 51

Brand: LIFTINGITALIA Pages: 24

Brand: FARFISA INTERCOMS Pages: 2

Brand: Toa Pages: 6

Brand: Clear-Com Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands