manualshive.com logo in svg

Allen-Bradley 5069-IA16, User Manual

The Allen-Bradley 5069-IA16 is a high-quality input module utilized in various industrial automation applications. Maximize the functionality of this product by referencing the comprehensive User Manual provided on our manualshive.com, available for free download. Empower your work with detailed instructions and essential information at your fingertips.

Share
Download
background image

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

13

Preface

Terminology

The following table defines terms that are used in this manual.

Table 1 - Terminology Used throughout the Manual

Abbreviation

Full Term

Definition

1oo2

One out of Two

Identifies the programmable electronic controller architecture.

CIP™

Common Industrial Protocol

An industrial communication protocol that is used by Logix 5000-based automation systems on EtherNet/IP, 
ControlNet®, and DeviceNet® communication networks.

CIP Safety™

Common Industrial Protocol – 
Safety Certified

SIL-rated version of CIP.

—

Connection

Logical communication channel for communication between nodes. Connections are maintained and controlled 
between masters and slaves.

CL

Claim Limit

The maximum safety integrity level (SIL) that can be achieved.

DC

Diagnostic Coverage

The ratio of the detected failure rate to the total failure rate.

EN

European Norm.

The official European Standard.

GSV

Get System Value

A ladder logic instruction that retrieves specified controller status information and places it in a destination tag.

—

Multicast

The transmission of information from one sender to multiple receivers.

MTTF

Mean Time to Failure

The length of time that a device or other product is expected to remain reliable in operation.

NAT

Network Address Translation

The translation of an Internet Protocol (IP) address to another IP address on another network.

ODVA

Open DeviceNet Vendor Association

A nonprofit association of vendors that are established for the promotion of CIP networks.

PFD

Probability of a dangerous failure on 
demand 

The average probability of a system to fail to perform its design function on demand.

PFH

Average frequency of a dangerous 
failure per hour

The probability of a system to have a dangerous failure occur per hour.

PL

Performance Level

ISO 13849-1 safety rating.

—

Proof test

Periodic test that detects failures in a safety-related system so that, if necessary, the system can be restored to an 
as-new condition or as close as practical to this condition.

SC

Systematic Capability

A confidence that the systematic safety integrity meets the requirements of the specified safety integrity level 
(SIL). (from IEC 61508-4)

SFF

Safe Failure Fraction

The sum of safe failures plus the sum of dangerous detected failures divided by the sum of all failures.

SIL

Safety Integrity Level 

A relative level of risk-reduction that is provided by a safety function, or to specify a target level of risk reduction.

SIL CL

SL Claim Limit

The maximum safety integrity level (SIL) that can be achieved.

SNN

Safety Network Number 

Safety network number, which uniquely identifies a network across all networks in the safety system. You are 
responsible for assigning a unique number for each safety network or safety subnet within a system.

SRT

Safety Reaction Time

A consideration of delays or latencies within the safety system.

—

Standard

Devices or portions of devices that do not participate in the safety function.

—

Unicast

The transmission of information from one sender to one receiver.

Summary of Contents for 5069-IA16









































































































































































































































































































Reviews:

No comments

Related manuals for 5069-IA16

N-Com B901 Quick Manual preview
B901
Brand: N-Com Pages: 2
Bticino 363915 Installation Manual preview
363915
Brand: Bticino Pages: 84
Novus NVE-EP200 Installation Manual preview
NVE-EP200
Brand: Novus Pages: 11
Daewoo MC-5911SC Service Manual preview
MC-5911SC
Brand: Daewoo Pages: 21
Keurig DRINKWORKS Home Bar Classic Care Manual preview
DRINKWORKS Home Bar Classic
Brand: Keurig Pages: 32
Aqua Creek F-702RLNA-02 Manual preview
F-702RLNA-02
Brand: Aqua Creek Pages: 16
red lion ITMA Manual preview
ITMA
Brand: red lion Pages: 8
SONIQ Qplay QPC100 Operation Manual preview
Qplay QPC100
Brand: SONIQ Pages: 7
Tarfire SF-2200H Operating Manual preview
SF-2200H
Brand: Tarfire Pages: 31
IFM CompactModule CR2032 Device Manual preview
CompactModule CR2032
Brand: IFM Pages: 29
Hogtunes G4 SG KIT-RM Installation Manual preview
G4 SG KIT-RM
Brand: Hogtunes Pages: 12
MSW PROFRAME 600 User Manual preview
PROFRAME 600
Brand: MSW Pages: 7
National Instruments PCIe-784 R Series Getting Started preview
PCIe-784 R Series
Brand: National Instruments Pages: 14
T+A DD 820 M User Manual preview
DD 820 M
Brand: T+A Pages: 70
DriSteem VAPOR-LOGIC 3 Conversion Instructions preview
VAPOR-LOGIC 3
Brand: DriSteem Pages: 4
Riello 7200/1 170 Plus Installer And User Manual preview
7200/1 170 Plus
Brand: Riello Pages: 16
Vestil CYL-P-LUG Series Instruction Manual preview
CYL-P-LUG Series
Brand: Vestil Pages: 7
QTS AN-X2-MOD-MON User Manual preview
AN-X2-MOD-MON
Brand: QTS Pages: 61

Brands by name

Popular brands

Load more brands