background image

Rockwell Automation Publication 2711P-UM006E-EN-P - January 2017

23

Overview

Chapter 1

1250 Model

2711P-RDK12C

Keypad

12.1-in. color

2711P-RDK12CK

Keypad

2711P-RDT12C

Touch

2711P-RDT12CK

Touch

2711P-RDT12H

(1)

Keypad/Touch

2711P-RDT12AG

Touch

2711P-RDB12C

Keypad/Touch

2711P-RDB12CK

Keypad/Touch

1500 Model

2711P-RDK15C

Keypad

15-in. color

2711P-RDT15C

Touch

2711P-RDT15AG

Touch

2711P-RDB15C

Keypad/Touch

(1) H at end of cat. no. refers to 1250 High-bright display module.

Table 15 - Display Modules - 700 to 1500 Terminals

Cat. No.

Input Type

Display

Marine 

Certified

Conformal

Coated

Built-in

Antiglare Overlay

Table 16 - Logic Modules - 700 to 1500 Terminals

Cat. No.

Power 

Input

Memory

RAM/Nonvolatile

Communication

Marine 

Certified

Conformal

Coated

Included Software

Without Standard Features

2711P-RP8A

AC

512 MB/512 MB 

(approximately 79 MB 

free user memory)

Ethernet

RS-232

Network interface for 
communication module

Windows CE 6.0 operating system 

FactoryTalk View Machine Edition runtime, 
version 6.0 or later

FactoryTalk ViewPoint software, 
version 1.2 or later

2711P-RP8D

DC

2711P-RP8DK

DC

With Extended Features

2711P-RP9A

AC

512 MB/512 MB 

(approximately 79 MB 

free user memory)

Ethernet

RS-232

Network interface 
communication module

Windows CE 6.0 operating system 
with extended features and file viewers

FactoryTalk View Machine Edition runtime, 
version 6.0 or later

FactoryTalk ViewPoint software, 
version 1.2 or later

2711P-RP9D

DC

2711P-RP9DK

DC

Table 17 - Communication Modules - 700 to 1500 Terminals

Cat. No.

Communication

Conformal
Coated

Marine 
Certified

Ethernet

DH+

DH-485

ControlNet 

(2)

(2) Scheduled and unscheduled communication.

2711P-RN6

2711P-RN6K

2711P-RN15S

2711P-RN15SK

2711P-RN20

(1)

(1) All terminals have an Ethernet port. The cat. no. 2711P-RN20 module provides an additional Ethernet port.

Summary of Contents for 2711P-B10C4A8





























































































































































































Reviews: