manualshive.com logo in svg

Allen-Bradley 1756-M02AE, User Manual, Page: 188 / 236

Share
Download
Allen-Bradley 1756-M02AE User Manual Download Page 188

Chapter 4 

Geometries with orientation support 

 

188

 

Rockwell Automation Publication MOTION-UM002F-EN-P - February 2018 

Coupling Ratio J4:J5

 

   

The parameter is only available when 

Coupling Direction

 is set to 

Same

 or 

Opposite

. It includes a Swing Arm Coupling Ratio Numerator and a Swing Arm 

Coupling Ratio Denominator.   

 

The 

Numerator

 is the first value of the Coupling Ratio parameter. It represents J4 

axis rotation as a reference for J5 axis move. 

The 

Denominator

 is the second value of the Coupling Ratio parameter. It 

represents J5 axis rotation caused by J4. 

For example, if the J4 axis is moving by 10 degrees (or revs) and causes the 5 

degrees (or revs) of tilt movement, then the coupling ratio between J4:J5 should be 

set as 2:1. 

Tip: 

Both rotations should be measured in same units (degree or rev.) The 

Numerator

 and 

Denominator

 default to 1 

and cannot be set to zero. 

See also 

Configuration parameters for Delta J1J2J3J4J5 robot

 on 

page 180

 

For Delta robot geometries, the internal transformation equations in the Logix 

Designer application assume: 

•

 

Joints (J1, J2, and J3) are at 0   when link L1 is horizontal in the XY plane. 

•

 

As each top link (L1) moves downward, its corresponding joint axis (J1, J2, 
or J3) is rotating in the positive direction. 

•

 

Joint 4 axis of rotation is aligned with Z axis and Joint 5 axis or rotation is 

aligned with Y axis of the base frame. When J4 and J5 is at 0 , End of Arm 
(EOA) frame is rotated by 180   on Rx (Z axis pointing down) with 

respect to base frame. 

To have joints J1, J2, and J3 angular positions to be any value other than 0 when 

L1 is horizontal, then configure the 

Zero Angle Orientation 

values on the 

Geometry

 tab in the 

Coordinate System Properties

 dialog box to align the joint 

angle positions with the internal equations. 

For example, if the Delta robot is mounted so that the joints attached at the top 
plate are homed at 30   in the positive direction below horizontal and you want 

the readout value in the application to be zero in this position, then enter -30   in 
the 

Z1

, 

Z2

, and 

Z3

 parameters on 

Geometry

 tab. 

Configure Zero Angle 

Orientations for Delta 
J1J2J3J4J5 robot 

Summary of Contents for 1756-M02AE













































































































































































































































Reviews:

No comments