manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, User Manual, Page: 31 / 176

Share
Download
Allen-Bradley 1732ES-IB12XOB4 User Manual Download Page 31

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

31

About the Modules

Chapter 2

I/O Module Overview

The Guard I/O modules implement the CIP Safety™ protocol extensions over 
EtherNet/IP networks and provide various features for a safety system.

Use the modules to construct a safety-control network system that meets the 
following requirements, up to and including:

• Safety Integrity Level Claim Limit 3 (SIL CL 3), as defined in 

IEC 61508

• Category 4 (CAT. 4), Performance Level e (PLe), as defined in 

ISO 13849-1

Remote I/O communication for safety I/O data is performed through safety 
connections that support CIP Safety over an EtherNet/IP network, and data 
processing is performed in the safety controller.

A safety controller monitors the status and fault diagnostics of the I/O 
modules through a safety connection by using a new or existing EtherNet/IP 
network.

Summary of Contents for 1732ES-IB12XOB4

















































































































































































Reviews:

No comments