manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, User Manual, Page: 28 / 176

Share
Download
Allen-Bradley 1732ES-IB12XOB4 User Manual Download Page 28

28

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Chapter 2

About the Modules

Firmware Information and 
Downloads

Verify that the Guard I/O firmware revision is correct before you commission 
the safety system. Firmware information and downloads for safety modules are 
available at this link:

http://www.rockwellautomation.com/rockwellautomation/support/
pcdc.page

.

Functional Safety 
Certificates

Safety certificates for Functional Safety modules are available at this link: 

http://www.rockwellautomation.com/global/certification/overview.page

Understand Suitability for 
Use

Rockwell Automation is not responsible for conformity with any standards, 
codes, or regulations that apply to the combination of products in your 
application or use of the product.

Take all necessary steps to determine the suitability of the product for the 
systems, machine, and equipment with which it is used.

Know and observe all prohibitions of use applicable to this product.

Never use the products for an application that involves serious risk to life or 
property without making sure of the following:

• The system as a whole is designed to address the risks.
• The Rockwell Automation product is properly rated and installed for 

the intended use within the overall equipment or system.

Use the module only in an environment that is within the general specifications 
of the module.

Summary of Contents for 1732ES-IB12XOB4

















































































































































































Reviews:

No comments