Allegion Interflex IF-57 Series Manual Download Page 20

Page: 20 / 22

5 Technical specifications

4. Reset switch position:

Associated console command:

factory-reset full

5 Technical specifications

Power supply

Nominal voltage

18 to 24 V AC/DC

Power supply via Ethernet

PoE IEEE 802.3at of power class 0 (up to 13 W)

Power consumption

Max. 12 VA

Fuse

PTC resistor

Equipment

Credential reader

RFID: MIFARE® Classic/DESFire, LEGIC® advant/prime or
(F-5735 only (SimonsVoss ‘Active Technology")
IF-5735: BLE

Read range

RFID 40 cm, BLE optional

Display

Capacitive 4.3 inch color display; resolution of 480 x 272 pixels

Keypad

IF-5735: PIN entry possible

Signaling

Audible: Buzzer
Visual: Color LEDs

Data interfaces

Ethernet network connection with SSH
TTL service interface

Inputs

IF-5735: Up to two I/O controller boards with 2 floating sensors
each (optional)

Output relay/switching capacity

IF-5735: Up to two I/O controller boards with 1 floating sensors
each (optional), max. 30 V / 2 A

Anti-tamper switch

Anti-tamper switch, activated when front panel is removed

General data

Degree of protection

IP30 (with concealed wiring)

Summary of Contents for Interflex IF-57 Series























Search results

Summary of Contents for Interflex IF-57 Series

Reviews:

Related manuals for Interflex IF-57 Series

Brands by name

Popular brands

Allegion Interflex IF-57 Series, Manual

Search results

Summary of Contents for Interflex IF-57 Series

Reviews:

Related manuals for Interflex IF-57 Series

Brands by name

Popular brands