1
www.observint.com
ALI-NS2012R-23R_CQ
170425
2.
Route an Ethernet cable from your network switch or network video recorder, and the camera
mounting location. The camera can be powered with PoE, or through a 12 Vdc source. If powering
the camera from a 12 Vdc power source, route the power cable to from the power source to the
mounting location. Power plug polarity is shown in the drawing to the right.
Do not apply power
to the power cable at this time.
3.
See the drawing to the right. Rotate the trim
ring counter-clockwise, and then lift it off the
camera assembly.
4.
Loosen the lock screw, and then separate the
enclosure and turret module from the base.
Base
Trim ring
Enclosure and
turret module
Lock screw
5.
Unscrew the maintenance access cover from
the side of the turret module.
6.
Insert a microSD card into the card slot as in
the drawing on the right. Push the card in
until it is fuly seated and locks into place.
7.
Reinstall the maintenance access cover.
microSD
card
RST (reset) button*
Maintenance
access cover
*
To restore the camera with its default configuration (including
user name, password, IP address, etc. press and hold the
RST
button for 10s when the camera is power on or rebooting.
8.
Use the drill template to mark holes for the
mounting screws and drop cable hole in the
surface.
9.
Drill holes in the mounting surface for the
mounting screws, and drop cable, if needed.
10. Attach the base to the mounting surface using
three screws. If the drop cable will be routed
through the side of the base, lay the drop
cable through a cable channel in the base
before tightening the screws.
Mounting surface
Base
Screws
11. To reassemble the camera,
a.
Connect the Ethernet LAN cable to the camera LAN drop cable. Protect the connection from
moisture and other contamination, if necessary. A Weatherproof Ethernet Fitting is provided.
Installation instructions for the fitting are included at the end of this document.
Camera
Ethernet switch
Network drop cable
from camera
Network cable from
router or switch
Weatherproof Ethernet Fitting installed
WARNING
!
Failure of the power or Ethnernet connector due to moisture or another
contaiminant is considered an installation error, which voids the waranty. If
installing this camera in a location such as an overhang, shop, garage, kitchen, etc.
where high humidity or dust is present, seal these connections adequately.
b.
If the camera is not powered using PoE (Power over Ethernet injector), connect the 12 Vdc
power cable to the camera drop cable. The polarity of the drop cable connector is shown
below.
ALI-NS2012R, ALI-NS2023R
Low Light IP Turret Camera
Quick Installation Guide
This document guides you through the basic steps to install and configure the ALI-NS2012R and
ALI-NS2023R cameras. These cameras feature:
•
Sony Low Light 0.005 Lux sensor
•
Compression standards include H.265, H.265+, H.264+, H.264, MJPEG
•
2.8mm Lens
•
120 dB Wide Dynamic Range, 3D Digital Noise Reduction
•
Full Frame Illumination Smart IR array
•
Advanced video analytics
•
Supports onboard storage, 128GB max microSD (Not Included)
•
IP67, temperature rnge -22 °F ~ 140 °F
For more information about the features of these cameras, please refer to the
AlibiSecurity.com/Resources.
Turret
Enclosure
Ethernet connector
Power Connector
Trim ring
Lens
IR LED
What’s in the box
Box contains this document with the items shown below.
Drill Template
Weatherproof
Ethernet fitting
Mounting
screws and
wall inserts
Step 1. Install the camera
Before installing the camera,
•
Make sure the device in the package is in good condition and all the assembly parts are included.
•
Make sure your power source matches the requirements for your camera. Power requirements are
shown in the
Specifications
section at the end of this document.
•
Check the
Specifications
section for the recommended installation environment.
•
Make sure that the mounting surface is strong enough to withstand four times the weight of the
camera (and the bracket, if used).
•
Make sure the field of view has no reflective surfaces close to the IR emittter of the camera. These
surfaces can bounce IR light back onto the camera lens, limiting performance in dark environments.
1.
Determine the best fasteners for securing the camera to mounting surface. The mounting hardware
provided is suitable for most surfaces. Note that the drop cable can be routed through the mounting
surface, or out the side of the base and trim ring.
