background image

1

www.observint.com

ALI-NS1012VRP_CQ 

190924

What’s in the box

Your camera includes: 

• 

Camera assembly

• 

Drill template

• 

Waterproof Ethernet Fitting

• 

Security L-wrench 

• 

Mounting screws and wall inserts

• 

Installation guide (this document)

• 

Alibi IP Camera Network Setup Guide

Security L-wrench and mounting hardware 

Step 1.  Before installing the camera ...

The ALI-NS1012VRP camera can be installed on a ceiling, wall or table, or installed with any of the optional 
accessories listed above. 
1. 

Check the package contents and make sure that the device in the package is in good condition and 
all the assembly parts are included. 

NOTE

: Do not remove the protective film on the lens until the 

camera is mounted and you are ready to power it on.

2. 

Make sure the mounting surface and fasteners are strong enough to withstand at least three times 
the weight of the camera assembly and the mounting bracket (if used). For concrete or cement 
block walls, use an expansion screw to secure the camera or mounting bracket. 

3. 

Make sure all the equipment that will be attached to the camera is power-off during the installation, 
if possible.

4. 

Check the specification of the products for the installation environment.

5. 

Make sure the power supply is matched with the camera voltage and wattage specification to avoid 
damage.

6. 

Make sure that there are no reflective surface too close to the camera lens. The IR light from the 
camera may reflect back into the lens causing reflection.

7. 

Do not remove the dome cover film until the installation is finished. Dust or grease on the dome 
cover will cause IR reflection. If there is dust or grease on the dome cover, clean the dome cover with 
clean soft cloth and isopropyl alcohol. 

Step 2.  Prepare the camera for installation 

Remove the Bezel 

1. 

Remove the camera assembly from the packaging. Do not remove the plastic film from that covers 
the lens at this time. 

2. 

Lay the camera on a clean, flat surface with the lens side up. 

3. 

Open the Bezel Lock Screw cover. 

Bezel Lock Screw 

Shown with cover removed

Bezel

4. 

Use the security L-wrench to fully unscrew the bezel lock screw. 

NOTE

: The bezel lock screw is a 

captive screw. 

5. 

Unsnap the cover from the camera assembly. 

6. 

Unsnap the bezel from the camera assembly. If the bezel cannot be separated from the camera 
assembly, turn the camera base side up and push a small blade screwdriver into the slots shown in 
the photo below to free the three bezel retention tabs from catches on the camera assembly. 

ALI-NS1012VRP Panoramic 12 MP IP Camera 
Quick Installation Guide

This document guides you through the basic steps to install and configure the ALI-NS1012VRP camera. This 
camera features: 

• 

1/1.7” progressive scan CMOS with 4000 × 3000 pixel resolution @ 30 fps

• 

360° fisheye panoramic view

• 

Multiple viewing modes

• 

Internal microSD / SDHC / SDXC card slot for storage up to 256 GB (card not provided)

• 

1

X

 alarm IN and OUT 

• 

Built-in microphone and speaker, supports external microphone and speaker

• 

50 ft IR range

• 

Compatible with these accessories: ALI-AF8 flange adapter, ALI-AJ3 angled surface mount junction 
box, ALI-AJ12 Pro VF turret flange.

For more information about the software features of this camera, please refer to the 

ALI-IP Camera 

Firmware User Manual

Bezel

Fisheye Lens

IR LEDs (3)

Bezel lock screw  

under cover.

Speaker and microphone

ALI-NS1012VRP camera 

12 Vdc  

Power

Audio  

LINE IN

Audio  

LINE OUT

Alarm  

IN/OUT

RJ-45 LAN 

connector

RS-485  

D+, D-

Product 

label

Underside of camera with drop cables

Reviews: