manualshive.com logo in svg

ALGE-Timing TdC 8000, Manual, Page: 32 / 108

Share
Download
ALGE-Timing TdC 8000 Manual Download Page 32

TdC 8000 for Equestrian 

               

Page 32

Version:E-00-08-08

Page 32

5.

MAIN MENU - GENERAL ADJUSTMENTS

The TdC 8000 is a very universal timing device. To cover a wide range of timing solutions it is
possible to adjust each program individual. If you make changes in the main menu it stores this new
values after you turn the machine off.

Factory Default Setting:
If you want the have the ALGE standard configuration do the following:
-

turn TdC 8000 off (switch 26)

-

press <ALT> and <MENU> together and keep it pressed

-

turn TdC 8000 on (switch 26)

-

release <ALT> and <MENU> after five seconds

-

the main menu has now the ALGE standard configuration

You can also check and change the main menu set up through the RS 232 interface (see page 105,
chapter 8.2.1 and page 106, chapter 8.2.2).

How do you get into the main menu:
-

Select program

-

press <ALT> and <MENU> together

-

Press ¢ and £ to go through the menu. With the numeric keys of the finish keyboard (15) you

can select a menu direct.
-

Select the chosen menu with <YES>

Main Menu Selections:

Menu 1:

Delay Time Start = 1.00 s

Adjustable: from 0.01 to 9.99 seconds

Menu 2:

Delay Time Finish = 0.30 s

Adjustable: from 0.01 to 9.99 seconds

Menu 3:

Seconds Mode = OFF

Adjustable: ON or OFF

Menu 9:

Running Tenth = OFF

Adjustable: ON or OFF

Menu 11:

Finish Rank = ON

Adjustable: ON or OFF

Menu 15:

Print Menus = ON

Adjustable: ON or OFF

Menu 16:

Print Linefeed = 0

Adjustable from 0 to 9

Menu 17:

RS-232 Baudrate = 9600 Bd

Adjustable 2400, 4800, or 9600 Baud

Menu 18:

RS-232 Run time = OFF

Adjustable: ON or OFF

Menu 19:

D-Board Baudrate = 2400 Bd

Adjustable: only 2400 Baud

Menu 20:

D-Board Channel 2 = RUNNING

Adjustable: RUNNING or STANDING

Menu 21:

Beep = ON Adjustable:

ON or OFF

Menu 24:

Change RunAdjustable:

SAME or NEXT run

Menu 25:

Change Race

You can select another race

Menu 26:

D-Board-Test

Test program for the display board

Menu 37:

Time Violation 1 = 0.25

Adjustable: 0 to 99.99

Menu 38:

Time Violation 2 = 1

Adjustable: 0 to 99.99

Menu 39:

Parcour Time 1 = 000.00

Adjustable: 0 to 999.99

Menu 40:

Parcour Time 1 = 000.00

Adjustable: 0 to 999.99

Menu 41:

Block Time 1 = 000.00

Adjustable: 0 to 999.99

Menu 42:

Block Time 2 = 000.00

Adjustable: 0 to 999.99

Menu 43:

Count Down Time 1 = 1 min.

Adjustable: 0 to 23:59:59.99 or 0 to 6399.99

Menu 44:

Count Down Time 2 = 1 min.

Adjustable: 0 to 23:59:59.99 or 0 to 6399.99

Menu 45:

D-Board Count Down = ON

Adjustable: ON or OFF

Summary of Contents for TdC 8000













































































































Reviews:

No comments