background image

Warranty, Copyrights and Approvals 

WARRANTY 

 

Algas-SDI International, LLC (ASDI) warrants that the equipment is free of 
defects in materials and workmanship under normal use and service.  ASDI 
agrees to repair or replace, at our option, without charge f.o.b. factory, any part 
which has proven defective to the satisfaction of Algas-SDI International, LLC 
within one (1) year from the date of the original installation or within 18 months 
from the date of shipment, whichever is earlier.  Equipment, which in the opinion 
of ASDI, has been damaged by improper installation or operation, or has been 
abused or tampered with in any way, will not be accepted for return under 
warranty. 

Algas-SDI International, LLC will not accept back charges for work performed by 
others upon or in conjunction with ASDI equipment, unless prior authorization is 
given by means of an Algas-SDI International, LLC purchase order.  Algas-SDI 
International, LLC will not be liable by reason of shutdown, non-operation or 
increased expense of operation of other equipment, or any other loss or damage 
of any nature, whether direct or consequential, arising from any cause 
whatsoever. 

Algas-SDI International, LLC makes NO other warranty of any kind, whatsoever 
expressed or implied; and all warranties of merchantability and fitness for a 
particular purpose are hereby disclaimed by Algas-SDI International, LLC and 
excluded from these terms of sale.  No person has any authority to bind Algas-
SDI International, LLC to any representation or warranty other than this warranty. 

COPYRIGHT 

 

Copyright 2019 by Algas-SDI International, LLC, Seattle, Washington 98108. All 
rights reserved. No part of this manual may be reproduced or copied in any form 
or by any means, photographic, electronic, or mechanical, without the prior 
express written consent from Algas-SDI International, LLC, Seattle, Washington, 
USA. 

APPROVALS 

 

 

 

 

Summary of Contents for Direct Fired F6-ASME





















































Reviews: