manualshive.com logo in svg

Alfa Laval Gunclean Toftejorg T-82, Instruction Manual

Share
Download
Alfa Laval Gunclean Toftejorg T-82 Instruction Manual Download Page 9

Instruction Manual, Gunclean Toftejorg T-82 

Page 7 

Standard machines and machines delivered with ATEX certification 
in accordance with Directive 94/9/EC 
IM-TE91A052-EN4 

General description

 (continued) 

Standard configurations 

Connection 

Turbine/Inlet Guide 

Nozzles (mm) (3/4” thread conn.) 

Article/Ref. No. 

Fixed with 127mm 
o.d. Flange  

50% 

2xø7 

TE21F002 

100% 

2xø8 
2xø9 

TE21F012 
TE21F014 

0% 

2xø10 

TE21F020 

Connection 

Turbine/Inlet Guide 

Nozzles (mm) (3/4” thread conn.) 

Article/Ref. No. 

Fixed  
Without flange 

50% 

2xø7 

TE21F032 

100% 

2xø8 
2xø9 

TE21F042 
TE21F044 

0 % 

2xø10 

TE21F050 

 

 

Connection 

Turbine/Inlet Guide 

Nozzles (mm) (3/4” thread conn.) 

Article/Ref. No. 

Portable with 1½” 
BSP Nipple 

50% 

2xø7 

TE21F202 

100% 

2xø8 
2xø9 

TE21F212 
TE21F214 

0 % 

2xø10 

TE21F230 

Connection 

Turbine/Inlet Guide 

Nozzles (mm) (3/4” thread conn.) 

Article/Ref. No. 

Portable with 1½” 

NPT Nipple 

50% 

2xø7 

TE21F262 

100% 

2xø8 
2xø9 

TE21F272 
TE21F274 

0 % 

2xø10 

TE21F280 

 
The hub of the machine is equipped with a clutch in the hub, which gives the possibility of rotation by 
hand the nozzles, when the machine is to be lifted out through a tank opening. 
 
 

Standard Options 

Machines with nozzle extensions for longer throw length can be supplied as an option. Same article no. 
with index no. –22. e.g. TE21F002-22.  
 
Machines with e-gear and nozzle extension: Same article no. with index no. -62, e.g. TE21F002-62. 
Only available for Gunclean Toftejorg T-82F). 
 
 

Available add-ons 

ATEX, category 1 for installation in zone 0/20 
-  TE21FXXX-70 ATEX 
-  TE21FXXX-22-70 ATEX + nozzle extension 
-  TE21FXXX-62-70 ATEX + nozzle extension and E-gear 

(only available for Gunclean Toftejorg T-82F) 

 

Explanation to Add-ons 

ATEX, category 1 for installation in zone 0/20 in accordance with Directive 94/9/EC

 

Summary of Contents for Gunclean Toftejorg T-82




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands