background image

Open Problem Reports and Feature Exceptions

page 66

OmniSwitch 6800/6850/9000—Release 6.1.3.R01

PR 106814

When DHCP Snooping is enabled against mobile port, sometimes the mobile port's VLAN ownership is 
not reflected in the DHCP Snooping port table.

Workaround: 

There is no known workaround at this time.

PR 106977

When DHCP Snooping is enabled, binding entry is not created against the new root port when STP topol-
ogy is changed.

Workaround: 

There is no known workaround at this time.

PR 107186

For DHCP Snooping feature, the CLI should not allow user to configure ip-source-filtering on a trusted 
port. However, if the port is a member of a link aggregate, the CLI does not display an error and allows the 
configuration.

Workaround: 

Make sure the port is not a member of a link aggregate before configuring the ip-source-

filtering.

IPv6

Problem Reports

PR 86669

On an OS6850/OS9000, IPv6 Router Advertisement decrementing timers are not supported for prefix 
valid lifetimes or prefix preferred lifetimes.

Workaround: 

Use IPv6 Router Advertisement fixed timers.

PR 91228

An OS6850 does not detect IPv6 port scanning or other IPv6 denial of service attacks.

Workaround: 

There is no known workaround at this time.

PR 94546

An OS9000 does not make use of the MTU interface configured via the 

IPv6 interface

 command and only 

supports the port MTU. Therefore, even if the configured IPv6 interface MTU is smaller, packets will still 
be forwarded instead of being dropped and “a packet too big” message returned to the sender. This can 
cause problems with path MTU discovery.

Workaround: 

There is no known workaround at this time.

Summary of Contents for OmniSwitch 6800























































































Reviews: