Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 994

Page: 994 / 2018

LINK OAM Commands

page 26-26

OmniSwitch 6250 CLI Reference Guide

November 2009

show efm-oam configuration

Displays the global LINK OAM configuration.

show efm-oam configuration

Syntax Definitions

N/A

Defaults

N/A.

Platforms Supported

OmniSwitch 6250.

Usage Guidelines

•

Use this command to display the global configuration of LINK OAM.

Examples

-> show efm-oam configuration

EFM OAM Status : enabled,

Multiple PDU Count : 5

Output fields are described here:

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaDot3OamStatus

alaDot3OamMultiplePduCount

output definitions

EFM OAM status

The current administrative status of LINK OAM on this switch
(

Enabled

Disabled

Multiple PDU Count

The number of PDUs sent when LINK OAM needs to send multiple
Event Notification.

efm-oam

Enables or disables the LINK OAM protocol on the switch.

show efm-oam port detail

Displays the LINK OAM configuration and other related parame-
ters for a port.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 994 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: