Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 897

Page: 897 / 2018

VLAN Stacking Commands

OmniSwitch CLI Reference Guide

November 2009

page 24-35

show ethernet-service sap

Displays configuration information for VLAN Stacking Service Access Points (SAP).

show ethernet-services sap [sapid]

Syntax Definitions

sapid

The SAP ID number identifying the service instance.

Defaults

By default, all SAPs are displayed if a SAP ID is not specified with this command.

Platforms Supported

OmniSwitch 6250-Metro Models

Usage Guidelines

Specify a single SAP ID to display configuration information for a specific SAP.

Examples

-> show ethernet-services sap

SAP Id : 10

UNIs : 2/10, 2/11

CVLAN(s) : 500, 600

sap-profile : default-sap-profile

SAP Id : 20

UNIs : 1/1, 1/2

CVLAN(s) : 10, 20

sap-profile : sap-video1

SAP Id : 30

UNIs : 1/3

CVLAN(s) : 30, 40

sap-profile : sap-video2

-> show ethernet-service sap 10

SAP Id : 10

UNIs : 2/10, 2/11

CVLAN(s) : 500, 600

sap-profile : default-sap-profile

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 897 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: