manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 883 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 883

VLAN Stacking Commands

OmniSwitch CLI Reference Guide

November 2009

page 24-21

ethernet-service sap sap-profile

Associates a VLAN Stacking Service Access Point (SAP) with a SAP profile. This command is also used 
to change an existing SAP profile association.

ethernet-service sap sapid sap-profile sap-profile-name 

Syntax Definitions

sapid

The SAP ID number (2–4094).

sap-profile-name

The name of the SAP profile to associate with this SAP ID.

Defaults 

The “default-sap-profile” profile is automatically associated with the SAP ID when the SAP is created.

Platforms Supported

OmniSwitch 6250-Metro Models

Usage Guidelines

•

If a profile association already exists for the specified SAP ID, the current profile is replaced with the 
profile specified with this command.

•

The SAP ID specified with this command must already exist. Use the 

ethernet-service sap

 command 

to create a SAP.

•

The SAP profile specified with this command must already exist. Use the 

ethernet-service sap-profile

 

command to create a SAP profile. 

•

To change the profile associated with the SAP back to the default profile, enter “default-sap-profile” 
with this command. 

•

Note that if the SAP ID specified with this command is associated with an IPMVLAN, the profile asso-
ciated with the SAP ID must specify CVLAN tag translation. Double tagging is not supported with 
IPMVLAN SAPs that are also associated with a UNI port.

•

Do not specify a service name; doing so will return an error message. This command is only for associ-
ating an existing profile to a VLAN Stacking SAP.

Examples

-> ethernet-service sap 10 sap-profile CustomerC

-> ethernet-service sap 11 sap-profile CustomerD

Release History

Release 6.6.1; command was introduced.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments