Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 850

Page: 850 / 2018

GVRP Commands

page 23-24

OmniSwitch 6250 CLI Reference Guide

November 2009

show gvrp configuration

Displays the global configuration for GVRP.

show gvrp configuration

Syntax Definitions

N/A

Defaults

N/A

Platforms Supported

OmniSwitch 6250

Usage Guidelines

N/A

Examples

-> show gvrp configuration

GVRP Enabled : yes,

Transparent Switching Enabled : no,

Maximum VLAN Limit : 256

Release History

Release 6.6.1; command was introduced.

output definitions

GVRP Enabled

Indicates whether or not GVRP is globally enabled.

Transparent Switching
Enabled

Indicates whether transparent switching is enabled (

Yes

) or disabled

(

). When enabled, GVRP messages are flooded even if GVRP is dis-

abled for the switch.

Maximum VLAN Limit

The maximum number of VLANs that can be learned by GVRP in the
system.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 850 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: