Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 411

Page: 411 / 2018

802.1AB Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 13-19

show lldp system-statistics

Displays system-wide statistics.

show lldp system-statistics

Syntax Definitions

N/A

Defaults

N/A

Platforms Supported

OmniSwitch 6250

Usage Guidelines

N/A

Examples

-> show lldp system-statistics

Local LLDP Agent System Statistics:

Remote Systems Last Change = 0 days 0 hours 3 minutes and 10 seconds,

Remote Systems MIB Inserts = 2,

Remote Systems MIB Deletes = 0,

Remote Systems MIB Drops = 0,

Remote Systems MIB Age Outs = 0

Release History

Release 6.6.1; command was introduced.

output definitions

Remote Systems Last Change

The last change recorded in the tables associated with the remote sys-
tem.

Remote Systems MIB Inserts

The total number of complete inserts in the tables associated with the
remote system.

Remote Systems MIB Deletes

The total number of complete deletes in tables associated with the
remote system.

Remote Systems MIB Drops

The total number of LLDPDUs dropped because of insufficient
resources.

Remote Systems MIB Age
Outs

The total number of complete age-outs in the tables associated with the
remote system.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 411 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: