manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 33 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 33

OmniSwitch 6250 CLI Reference Guide

November 2009

page 1-1

1   CMM Commands

The Chassis Management Module (CMM) CLI commands allow you to manage switch software files in 
the working directory, the certified directory, and the running configuration.

MIB information for the CMM commands is as follows:

Filename

:

AlcatelIND1Chassis.mib

Module

:

ALCATEL-IND1-CHASSIS-MIB

Filename

:

AlcatelIND1ConfigMgr.mib

Module

:

ALCATEL-IND1-CONFIG-MGR-MIB DEFINITIONS

A summary of available commands is listed here:

reload
reload working
copy running-config working
write memory
copy working certified
copy working certified
copy flash-synchro
takeover
show running-directory
show reload
show microcode
show microcode history

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments