manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 250 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 250

File Management Commands

page 7-38

OmniSwitch 6250 CLI Reference Guide

November 2009

view

Allows you to view the contents of a specified file by invoking the Vi text editor in read-only mode.

view [path/]filename

Syntax Definitions

path

The path directory leading to the file being viewed. If no path is speci-
fied, the command assumes the current directory.

filename

The name of the existing file being viewed. Up to thirty-two (32) char-
acters may be used (e.g., 

test_config_file

).

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

This command can also be used on the secondary CMM. 

Examples

-> view flash/text_file.txt

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

systemServices

systemServicesArg1

systemServicesAction

vi

Launches the switch’s Vi text editor.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments