manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1878 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1878

AAA Commands

page 43-38

OmniSwitch 6250 CLI Reference Guide

November 2009

user password-policy min-digit

Configures the minimum number of base-10 digits required for a valid password.

user password-policy min-digit number

Syntax Definitions

number

The minimum number of digits. The range is 0 to 7.

Defaults

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Specify 

0

 with this command to disable the minimum number of digits requirement.

•

The minimum number of digits requirement is specified as part of a global password policy that is 
applied to all passwords when they are created or modified.

Examples

-> user password-policy min-digit 2

-> user password-policy min-digit 0 

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

aaaAsaConfig

aaaAsaPasswordMinDigit

parameter

default

number 

0

show user password-policy

Displays the global password policy configuration for the switch. 

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments