manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1727 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1727

IP Multicast Switching Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 41-9

ip multicast static-neighbor

Creates a static IGMP neighbor entry on a specified port on a specified VLAN.

ip multicast static-neighbor vlan vid port slot/port

no ip multicast static-neighbor vlan vid port slot/port

Syntax Definitions

vid

VLAN to include as a static IGMP neighbor.

slot/port

The slot/port number you want to configure as a static IGMP neighbor.

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Use the

 no

 form of this command to remove an IGMP static neighbor entry on a specified port on a 

specified VLAN.

•

The 

ip multicast static-neighbor 

command allows you to create an IGMP static neighbor entry on a 

specified port on a specified VLAN. This, in turn, enables that network segment to receive all the 
IGMP traffic.

•

You can also create an IGMP static neighbor entry on a link aggregate port by entering

ip multicast static-neighbor vlan vid port

, followed by the link aggregation group number

(e.g., ip multicast static-neighbor vlan 2 port 7).

Examples

-> ip multicast static-neighbor vlan 4 port 1/1

-> no ip multicast static-neighbor vlan 4 port 1/1

-> ip multicast static-neighbor vlan 4 port 7

-> no ip multicast static-neighbor vlan 4 port 7

Release History

Release 6.6.1; command was introduced.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments