manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1472 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1472

QoS Commands

page 38-44

OmniSwitch CLI Reference Guide

November 2009

qos port maximum egress-bandwidth

Configures the maximum rate at which to send traffic on the specified QoS port. 

qos port slot/port maximum egress-bandwidth bps

qos port slot/port no maximum egress-bandwidth

Syntax Definitions

slot/port

The slot number and port number of the physical port.

bps

The maximum amount of bandwidth that may be used for all traffic 
egressing on the QoS port. 

Defaults

By default, the maximum bandwidth is the maximum allowed for the interface type on which the port 
resides. 

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Use the 

no

 form of this command to remove a configured maximum egress bandwidth value from a 

port.

•

When configuring the maximum egress bandwidth for a combo port, specify the bandwidth value in 
multiples of 2Mbps. 

•

The maximum egress bandwidth value cannot exceed the maximum bandwidth of the interface type 
associated with the port.

•

Modifying the maximum egress bandwidth is most useful for low-bandwidth links.

Examples

-> qos port 3/1 maximum egress-bandwidth 1000

-> qos port 3/1 no maximum egress-bandwidth

Release History

Release 6.6.1; command was introduced.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments