Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1445

Page: 1445 / 2018

QoS Commands

OmniSwitch CLI Reference Guide

November 2009

page 38-17

qos stats interval

Configures how often the switch polls network interfaces for statistics about QoS events.

qos stats interval seconds

Syntax Definitions

seconds

The number of seconds before the switch polls network interfaces for
statistics. The range is 10–3600.

Defaults

Platforms Supported

OmniSwitch 6250

Usage Guidelines

•

Change the statistics interval to a smaller interval if you want to monitor QoS events.

•

Change the statistics interval to a larger interval if you want to free some switch memory.

Examples

-> qos stats interval 30

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaQoSConfigTable

alaQoSConfigStatsInterval

parameter

default

seconds

show qos statistics

Displays statistics about the QoS configuration.

«
...
1443
1444
1445
1446
1447
...
»

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1445 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: