manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1279 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1279

DHCP Relay Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 32-3

ip helper address

Adds or deletes a DHCP server IP address. DHCP Relay forwards BOOTP/DHCP broadcasts to and from 
the specified address. If multiple DHCP servers are used, configure one IP address for each server. 

ip helper address ip_address 

ip helper no address [ip_address]

Syntax Definitions

ip_address

DHCP server IP address (e.g. 21.0.0.10). 

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Using this command enables a Global DHCP Relay service on the switch. When the DHCP Relay is 
specified by the DHCP server IP address, the service is called Global DHCP.

•

When the DHCP Relay is specified by the VLAN number of the DHCP request, the service is referred 
to as Per-VLAN DHCP.

•

Global DHCP and Per-VLAN DHCP are mutually exclusive. You may only configure one or the other. 

•

Use the 

no

 form of this command to delete an IP address from the DHCP Relay service. If an address 

is not specified, then all addresses are deleted.

•

UPD Relay is automatically enabled on a switch when a DHCP server IP address is defined. There is 
no separate command for enabling or disabling the relay service.

•

Configure DHCP Relay on switches where packets are routed between IP networks.

•

You can configure up to 256 server IP addresses for one relay service.

Examples

-> ip helper address 75.0.0.10

-> ip helper no address 31.0.0.20

Release History

Release 6.6.1; command was introduced.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments