manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1183 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1183

IPv6 Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 30-17

ipv6 route

Configures a static entry in the IPv6 route. 

This command is currently not supported

. 

Please use the new 

 

ipv6 static-route

 

command

.

ipv6 route ipv6_prefix/prefix_length ipv6_address

 

[if_name]

no ipv6 route ipv6_prefix/prefix_length ipv6_address [if_name

]

Syntax Definitions

ipv6_prefix

IPv6 network that is the destination of this static route.

/prefix_length

The number of bits that are significant in the iPv6 address (mask). 
(0...128).

ipv6_address

IPv6 address of the next hop used to reach the specified network. 

if_name

If the next hop is a link-local address, the name of the interface used to 
reach it.

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

Use the 

no

 form of this command to remove a static route. 

Examples

-> ipv6 route 212:95:5::/64 fe80::2d0:95ff:fe6a:f458 v6if-137

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaIPv6StaticRouteTable

alaIPv6StaticRouteNextHop

alaIPv6StaticRouteIfIndex

alaIPv6StaticRouteDest

alaIPv6StaticRoutePrefixLength

alaIPv6StaticRouteRowStatus

show ipv6 routes

Displays IPv6 Forwarding Table. 

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments