manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1152 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1152

IP Commands

page 29-104

OmniSwitch 6250 CLI Reference Guide

November 2009

show icmp control

Allows the viewing of the ICMP control settings.

show icmp control

Syntax Definitions

N/A

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

Use this command to view the status of the various ICMP messages. It is also useful to determine the type 
and code of the less common ICMP messages.

Examples

-> show icmp control 

  Name                                 Type   Code   Status    min-pkt-gap(us)

-------------------------------------+------+------+---------+------------------

  echo reply                              0      0   enabled             0

  network unreachable                     3      0   enabled             0

  host unreachable                        3      1   enabled             0

  protocal unreachable                    3      2   enabled             0

  port unreachable                        3      3   enabled             0

  frag needed but DF bit set              3      4   enabled             0

  source route failed                     3      5   enabled             0

  destination network unknown             3      6   enabled             0

  destination host unknown                3      7   enabled             0

  source host isolated                    3      8   enabled             0

  dest network admin prohibited           3      9   enabled             0

  host admin prohibited by filter         3     10   enabled             0

  network unreachable for TOS             3     11   enabled             0

  host unreachable for TOS                3     12   enabled             0

  source quench                           4      0   enabled             0

  redirect for network                    5      0   enabled             0

  redirect for host                       5      1   enabled             0

  redirect for TOS and network            5      2   enabled             0

  redirect for TOS and host               5      3   enabled             0

  echo request                            8      0   enabled             0

  router advertisement                    9      0   enabled             0

  router solicitation                    10      0   enabled             0

  time exceeded during transmit          11      0   enabled             0

  time exceeded during reassembly        11      1   enabled             0

  ip header bad                          12      0   enabled             0

  required option missing                12      1   enabled             0

  timestamp request                      13      0   enabled             0

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments