Alcatel-Lucent 9927 Manuallines Download Page 67 | Manualshive

Page: 67 / 247

Alcatel-Lucent 9927 Manuallines Download Page 67

Line-up configuration

Purpose

This section describes the only line-up that is available for the 9927 Distributed Base
Station Outdoor Cabinet.

Line-up

At the present time, the only line-up available for the 9927 Distributed Base Station
Outdoor Cabinet consists of the 9927 Distributed Base Station Outdoor Cabinet and up to
two 60ECv2 battery cabinets.

The block diagram below shows the line-up for the 9927 Distributed Base Station
Outdoor Cabinet and two 60ECv2 battery cabinets.

60ECv2
Battery
Cabinet

60ECv2
Battery
Cabinet

P

Power

Optional

LEGEND

P

9927 Distributed BTS

Outdoor Cabinet

Site configurations for 9927 Distributed BTS Outdoor
Cabinet
Line-up configuration

Line-up configuration

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

9927 Dist BTS Outdoor
401-703-516
Issue 1

March 2012

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

4-3

«
...
65
66
67
68
69
...
»

Summary of Contents for 9927
























































































































































































































































Reviews:

No comments