manualshive.com logo in svg

Alcatel-Lucent 9927, Manuallines, Page: 136 / 247

Share
Download
Alcatel-Lucent 9927 Manuallines Download Page 136

Site preparation for GPS antenna

Introduction

This section describes how to perform site preparation for the GPS antenna.

Connection overview for GPS antenna

The GPS antenna is a receive-only antenna that requires only one antenna run. The GPS
antenna cable is terminated at the antenna support structure with a 7/16 DIN female
connector. At the antenna it is terminated with a 7/16 DIN-male connector. A gas tube
surge protector with DIN male/female connectors must also be installed. A jumper cable
connects the GPS antenna surge protector to the GPS antenna connector on the 9927
Distributed Base Station Outdoor Cabinet.

GPS cable connectors and surge protectors must be rated IP-67 or better. (IP-67 rating
requirement, as defined in IEC 60529, specifies total protection against dust and
protection against submersion in water.)

A side view of the GPS antenna connections are shown in the following diagram.

Recommended GPS antenna cable

Important!

The recommended cable type should be outdoor (UV) and riser (fire

retardant) rated.

The following table provides information for the recommended GPS antenna cable type.

Product Specification

Manufacturer (Reference)

Cable P/N
(Reference)

WP-93807 L3

OEM1

LDF4-RN-50A

On Antenna Cable

Antenna cable support

Jumper Cable

7/16 DIN-Male Connector

on Jumper Cable

7/16 DIN-Male Connector
on Jumper Cable

7/16 DIN-Female Connector

Antenna Cable

To

Antenna

Tower

Ground

Coaxial Cable Shield

Grounding

Ground

Surge Protector

* BB
(See Note)

Drip loop

* GPS jumper cable and field installed surge protector to 9927 Distributed BTS outdoor cabinet GPS port (1 place)

(

*Surge Protector at GPS port

9927
Distributed
BTS

Site preparation requirements for 9927 Distributed Base
Station Outdoor cabinet GPS antenna and microwave
antenna cable

Site preparation for GPS antenna

....................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................

10-4

Alcatel-Lucent – Proprietary

Use pursuant to applicable agreements

9927 Dist BTS Outdoor

401-703-516

Issue 1

March 2012

Summary of Contents for 9927
























































































































































































































































Reviews:

No comments