manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Preprovisioning Guidelines

Page 98

7750 SR OS Interface Configuration Guide

Preprovisioning Guidelines

7750 SR-Series routers have at least two ports, either located on SF/CPM modules or integrated 
into the chassis (on the 7750 SR-1series model), a console port and an auxiliary port, to connect 
terminals to the router.

 Configure parameters from a system console connected to a 7750 SR console port, using Telnet to 
access a 7750 SR remotely or SSH to open a secure shell connection.

Predefining Entities

In order to initialize a card, the chassis slot, line card type, and MDA type must match the 
preprovisioned parameters. In this context, 

preprovisioning

 means to configure the entity type 

(such as the line card type, MDA type, port, and interface) that is planned for a chassis slot, line 
card, or MDA. Preprovisioned entities can be installed but not enabled or the slots can be 
configured but remain empty until populated. 

Provisioning

 means that the preprovisioned entity is 

installed and enabled.

You can:

•

Preprovision ports and interfaces after the line card and MDA types are specified.

•

Install line cards in slots with no preconfiguration parameters specified. Once the card is 
installed, the card and MDA types must be specified.

•

Install a line card in a slot provisioned for a different card type (the card will not 
initialize). The existing card and MDA configuration must be deleted and replaced with 
the current information.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

D-Link Verizon DSL-2750B Setup Manual preview
Verizon DSL-2750B
Brand: D-Link Pages: 6
D-Link DIR-857 Quick Installation Manual preview
DIR-857
Brand: D-Link Pages: 10
D-Link DSL-2740U Quick Installation Manual preview
DSL-2740U
Brand: D-Link Pages: 38
Eaton Power Xpert Meter 2000 Instructions Manual preview
Power Xpert Meter 2000
Brand: Eaton Pages: 16
Eaton POW-R-COMMAND 1000 User Manual preview
POW-R-COMMAND 1000
Brand: Eaton Pages: 84
Safety Vision ROADRECORDER 8000 User Manual preview
ROADRECORDER 8000
Brand: Safety Vision Pages: 40
Javad TRIUMPH-3NR User Manual preview
TRIUMPH-3NR
Brand: Javad Pages: 35
NetComm 3GM1WN Quick Start Manual preview
3GM1WN
Brand: NetComm Pages: 3
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
TRENDnet TW-100 Specifications preview
TW-100
Brand: TRENDnet Pages: 2
Weidmuller IE-SW-VL16-14TX-2SC Hardware Installation Manual preview
IE-SW-VL16-14TX-2SC
Brand: Weidmuller Pages: 17
Xircom RealPort Ethernet 10/100 User Manual preview
RealPort Ethernet 10/100
Brand: Xircom Pages: 30
Tektronix CTS 850 User Manual preview
CTS 850
Brand: Tektronix Pages: 178
SAGEMCOM SE681 WiMAX User Manual preview
SE681 WiMAX
Brand: SAGEMCOM Pages: 75
Paradyne JetFusion 2100 Series User Manual preview
JetFusion 2100 Series
Brand: Paradyne Pages: 296
IBM EtherLink XL User Manual preview
EtherLink XL
Brand: IBM Pages: 72
Vaisala TERMBOX-9000 User Manual preview
TERMBOX-9000
Brand: Vaisala Pages: 32
Ruckus Wireless SmartZone 3.2 Quick Setup Manual preview
SmartZone 3.2
Brand: Ruckus Wireless Pages: 4

Brands by name

Popular brands

Load more brands