Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 426 | Manualshive

Page: 426 / 444

background image

Show Commands

Page 426

7750 SR OS Interface Configuration Guide

Port Monitor Commands

port

Syntax

port

port-id

[

port-id

...(up to 5 max)] [

interval

seconds

] [

repeat

repeat

] [

absolute

|

rate

]

[

multiclass

]

Context

monitor

Description

This command enables port traffic monitoring. The specified port(s) statistical information displays
at the configured interval until the configured count is reached.

The first screen displays the current statistics related to the specified port(s). The subsequent
statistical information listed for each interval is displayed as a delta to the previous display.

When the keyword

rate

is specified, the "rate per second" for each statistic is displayed instead of the

delta.

Monitor commands are similar to

show

commands but only statistical information displays. Monitor

commands display the selected statistics according to the configured number of times at the interval
specified.

Parameters

port

port-id —

Specify up to 5 port IDs. Port-IDs are only MLPPP bundles or bundle protection

groups when the multiclass keyword is specified.

Syntax:

port-id

slot/mda/port[.channel]

aps-id

aps-

group-id

[.

channel

]

aps

keyword

group-id

1 — 64

bundle ID

bundle-

type

-

slot/mda

.

bundle-num

bpgrp-

type

-

bpgrp-num

bundle

keyword

bundle-num 1 — 128
type

ima, ppp

interval

seconds —

Configures the interval for each display in seconds.

Default

10 seconds

Values

3 — 60

repeat

repeat —

Configures how many times the command is repeated.

Default

10

Values

1 — 999

absolute —

When the

absolute

keyword is specified, the raw statistics are displayed, without

processing. No calculations are performed on the delta or rate statistics.

rate —

When the

rate

keyword is specified, the rate-per-second for each statistic is displayed

instead of the delta.

«
...
424
425
426
427
428
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Brand: TDC Pages: 27

Brand: H3C Pages: 16

Brand: H3C Pages: 24

Brand: Paradyne Pages: 11

Brand: Paradyne Pages: 19

Brand: Paradyne Pages: 32

COMSPHERE 3550 Series

Brand: Paradyne Pages: 153

Jetstream CPX-1000

Brand: Paradyne Pages: 141

FrameSaver 9783

Brand: Paradyne Pages: 28

COMSPHERE 6800 Series

Brand: Paradyne Pages: 7

Brand: M86 Security Pages: 46

Brand: Qixiang Technology Pages: 16

Brand: ZyXEL Communications Pages: 116

Brand: Ravpower Pages: 27

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

Brand: ADDON Pages: 4

Brand: Idis Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands