manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 311 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 311

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 311

Forwarding Plane Commands

fp

Syntax

fp

 [

fp-number

]

Context

config>card

Description

The fp CLI node contains the multicast path management configuration commands for IOM-3 ingress 
multicast management. Ingress multicast management manages multicast switch fabric paths which 
are forwarding plane specific. On IOM-1 and IOM-2, each MDA has a dedicated forwarding plane 
and so have dedicated multicast paths to the switch fabric allowing the multicast management to be 
defined per MDA. IOM-3 has a single forwarding plane shared by two MDAs making the previous 
model of managing multicast at the MDA level problematic. The fp node has been added to simplify 
ingress multicast management on IOM-3.

In subsequent releases, the fp node will be moved to IOM-1 and IOM-2 and the multicast path 
management commands will be consistent for all IOM types. Other forwarding plane resource 
configuration commands (i.e. buffer pool management) are expected to also move to the fp node.

While IOM-3 only has a single forwarding plane, other IOMs that will use the node in the future will 
have multiple (i.e. IOM-1 and IOM-2). To accommodate multiple forwarding planes, each forwarding 
plane is assigned a number. The default forwarding plane is 1. When entering the fp node, if the 
forwarding plane number is omitted, the system will assume forwarding plane number 1. All show 
and save configuration output must include the forwarding plane number.

Parameters

fp-number — 

The fp-number parameter is optional following the fp command. If omitted, the system 

assumes forwarding plane number 1. More than a single forwarding plane will be supported in 
the future when IOMs other than IOM-3 are supported.

Values

1

Default

1

ingress

Syntax

ingress

Context

config>card>fp

Description

The ingress CLI node within the fp node contains the multicast path management configuration 
commands for IOM-3 ingress multicast management. For this release, on the bandwidth-policy 
command is supported within the ingress node.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments