Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 309

Page: 309 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 309

interval

Syntax

interval

interval

no interval

Context

config>redundancy>mc>peer>mcr>node>cv

Description

This command specifies the polling interval of the ring-node connectivity verification of this ring
node.

Default

Parameters

interval —

Specifies the polling interval, in minutes.

Values

1 — 6000

service-id

Syntax

service-id

service-id

no service-id

Context

config>redundancy>mc>peer>mcr>node>cv

Description

This command specifies the service ID of the SAP used for the ring-node connectivity verification of
this ring node.

Default

no service-id

Parameters

service-id —

Specifies the service ID of the SAP.

Values

1 — 2147483647

src-ip

Syntax

src-ip

ip-address

no src-ip

Context

config>redundancy>mc>peer>mcr>node>cv

Description

This command specifies the source IP address used in the ring-node connectivity verification of this
ring node.

Default

no src-ip

Parameters

ip-address —

Specifies the source IP address.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 309 / 444

Search results

Summary of Contents for 7750 SR OS

Reviews: