Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 268

Page: 268 / 444

Configuration Commands

Page 268

7750 SR OS Interface Configuration Guide

test-frequency

seconds

—

Specifies the frequency for testing for connectivity when the link is

establishing before polling begins.

Values

0 — 255

protocol

Syntax

protocol

protocol-type

no protocol

Context

config>port>sonet-sdh>path>atm>ilmi

Description

This command configures the protocol.

Parameters

protocol-type —

The

protocol-type

is an enumerated integer whose value indicates the ILMI version

of either 3.1 or 4.0 that is advertised by IME and also indicates the ILMI IME type of either user-
side or network-side.

Values

4_0-user, 4_0-network. 3_1-user, 3_1-network

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 268 / 444

Search results

Summary of Contents for 7750 SR OS

Reviews: