manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 237 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 237

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 237

Values

1 — 9000

re-authentication

Syntax

[

no

] 

re-authentication

Context

config>port>ethernet>dot1x

Description

This command enables / disables periodic 802.1x re-authentication.

When re-authentication is enabled, the 7750 SR will re-authenticate clients on the port every re-auth-
period seconds.

The 

no

 form of the command returns the value to the default.

Default

re-authentication

server-timeout

Syntax

server-timeout 

seconds

no server-timeout

Context

config>port>ethernet>dot1x

Description

This command configures the period during which the 7750 SR waits for the RADIUS server to 
responds to its AccessRequest message.  When this timer expires, the 7750 SR will re-send the 
AccessRequest message, up to max-request-number times.

The 

no

 form of this command returns the value to the default.

Default

30

Parameters

seconds — 

The server timeout period in seconds.

Values

1 — 300

supplicant-timeout

Syntax

supplicant-timeout 

seconds

no supplicant-timeout

Context

config>port>ethernet>dot1x

Description

This command configures the period during which the 7750 SR waits for a client to respond to its 
EAPOL messages. When the supplicant-timeout expires, the 802.1x authentication session is 
considered to have failed.

The 

no

 form of this command returns the value to the default.

Default

30

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments