manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 214 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 214

Configuration Commands

Page 214

7750 SR OS Interface Configuration Guide

los  — 

Reports loss of signal errors. When configured, 

los

 traps are not raised and cleared.

Default

los

 traps are issued.

oof  — 

Reports out-of-frame errors. When configured, 

oof 

alarms are not raised and cleared.

Default

oof

 alarms are not issued.

rai  — 

Reports resource availability indicator events. When configured, 

rai

 events are not raised and 

cleared.

Default

rai

 alarms are not issued

looped — 

Reports looped packets errors.

Default

looped

 alarms are not issued

scramble

Syntax

[

no

] 

scramble

Context

config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1>channel-group
config>port>tdm>e3

Description

This command enables payload scrambling on channel groups. 

Scrambling randomizes the pattern of 1s and 0s carried in a SONET frame. Rearranging or 
scrambling the pattern prevents continuous strings of all 1s or all 0s and meets the needs of physical 
layer protocols that rely on sufficient transitions between 1s and 0s to maintain clocking. 

For ATM, this command enables or disables ATM cell-level payload scrambling/descrambling using 
x43+1 polynomial as defined in ITU-T I.432.1. Scrambling is enabled by default for the ATM path/
channel. Note that this scrambling is done in addition to SONET/SDH frame scrambling/
descrambling, which is always enabled in the framer.

The 

no

 form of this command disables scrambling. 

Default

no scramble

keepalive

Syntax

keepalive 

time-interval 

[

dropcount

 

drop-count

]

no keepalive

Context

config>port>sonet-sdh>path>ppp
config>port>tdm>ds1>channel-group>cisco-hdlc
config>port>tdm>ds1>channel-group>ppp
config>port>tdm>ds3>ppp
config>port>tdm>e1>ppp
config>port>tdm>e3>ppp

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments